DIY popper made of polystyrene foam. How to make a homemade popper

You probably know that if you try to fish in shallow places or in heavily overgrown reservoirs, then such an amazing surface fishing bait as a popper can really help out. Let's make it with our own hands.

Step 1.

We will need a rectangular shaped block, like a fish. We adjust the parameters of the bar to the original shape, taking into account the allowance for grinding. Try to always create smooth surfaces, as well as right angles. After all, the quality of work of our new fish bait will depend in the future on the accuracy and symmetry of the manufactured Popper.

Then we draw the outline of the popper with a marker and then we cut it out (cut it out), but always with an allowance for further polishing.

Step 2.
We must symmetrically cut a symmetrical groove in the center of the fish simulator's abdomen using a metal blade (not deep yet - 1-2mm deep). We need it for laying fittings and ballast.

We do not deviate from the sample dimensions.

Step 3.
We round all the corners of the product one by one. Like from the belly of a fish.

Same from the side of her back.

Let's compare it with the original, achieving complete similarity with it. We sand the product with sandpaper and then saw the groove on the belly deeply.

Step 4.
But we will make the fish blade from plexiglass of a necessarily bright color, with a thickness of, say, 4 mm. First, heat it over the fire and squeeze it out as in Fig. This can be done by placing plexiglass over the corresponding hole. For such a hole, for example, the center of a circle of electrical tape or adhesive tape that happens to be nearby is suitable.

Cutting out the required part

We bring it to condition and then polish it..

At the front end we make a recess so that the blade can be attached without any gap.
Next we need stainless wire with a diameter of 0.8 mm. And a small strip of lead for ballast. Note that the thickness of the lead strip should fit into the sawn groove with little friction.
Using pliers and round-nose pliers, we make a frame, and then insert it, as can be seen in the figure, into the resulting cut in the abdomen.

Step 5.
Next, we drill a hole in the blades: the swivel, into which we will insert our popper, should be positioned as on the original. Take super glue and secure the blade. At the same time, we maintain the correct position and symmetry of the original itself.

Step 6.
Let's add lead to the groove on the belly of the fish simulator, while achieving the desired position of the bait when it hits the water. As you can see, balancing is not such a difficult thing. We take out the weights, and then insert them again, but with epoxy resin. We also fill the groove on the abdomen with it. The top of the product can be sprinkled with fine sawdust left over from sanding.
Let the resin dry, then file off the remaining resin. We polish the surface of the product. If dents appear during work, we remove them too. Large flaws can be eliminated with putty made from epoxy resin and sawdust.

The popper bait first appeared in America in the 30s, but it did not gain popularity immediately. Only in the 90s did fishermen begin to actively use it. Today this bait is considered one of best models.

A popper is a surface bait that makes a squelching sound when played. It attracts fish, causing them to rise from the bottom and swim to the surface in search of an irritant. It is considered incredibly catchy and effective, and can bring many trophies to the fisherman, if used correctly.

Popper with English language translated as “squish” or “gurgle.” The main feature of this model is its ability to make sounds and water fountains when wiring. They are the ones who attract predatory fish.

Photo 1. The orange notch in the front of the bait makes the same sound.

Popper was not the first, nor the only bait that could make sounds when played. In America, at the beginning of the last century, the first models appeared that floated on the surface and squelched. James Haddon noticed an unusual reaction of fish to any objects on the surface of the water. Over time, he founded a company that manufactured surface baits.

The first models were quite strange, they were equipped with one or more wooden propellers. A few years later, he created several series of lures without propellers; they were very vaguely reminiscent of poppers. Models that can be called “full-fledged poppers” appeared in the late 30s.

When positioned correctly, such baits quite realistically resemble a sick fish or an insect that has fallen on the water. There are a lot of models, they all differ in shape, size, appearance, loading and equipment.

Photo 2. Poppers for every taste.

Popper classification

The range of poppers is huge. They differ in many ways, but they are mainly classified according to the type of load. Poppers are:

• front loading;
• medium load;
• rear loading.

Advice! If you have to fish quite far from the shore, and you need a very long cast, then a rear-loading popper is best suited. After being thrown, the bait flies very accurately and sinks its heavy part into the water 35-40 cm. It is worth fishing in places where there is a space of 50 cm free from snags and algae.

In mid-load models, the weight is evenly distributed throughout the body, so the flight range is slightly worse. It enters the water flat, but does not sink more than 10-15 cm. Such models can be used in overgrown places where algae almost reaches the surface of the reservoir.

Attention! Front-loaded poppers are not able to fly very far when thrown, but they only submerge a few centimeters in the water. This feature allows them to be used in the most overgrown and impassable places for other baits.

It is better to catch them and throw them when the predator is not very active. Posting a popper allows you to interest almost any fish. And if you make several reels, the bait will sink deeper, which will provoke a throw.

DIY popper

Many fishermen prefer to make their own baits. After all, this allows you to create just such a model that will ideally suit the fishing conditions and will be able to catch exactly the fish you need. In addition, the cost homemade model much lower than purchased.

Such baits are made from a variety of materials; silicone popper, wood and plastic are considered incredibly catchy. A piece of wood can be used to make an excellent model for pike fishing.

You can take any tree, but it is better to give preference to birch and ash. Required materials and tools:

• wire;
• glue;
• sandpaper;
• file;
• tees with rings;
• coating varnish.

When all the materials have been collected and the required piece of wood has been found, you can proceed directly to the work itself. The stages of working on the bait are as follows:

1. From the beginning it is cut out with a knife future form calf, and with a file and sandpaper it will be improved. It is better to make a popper in the shape of a fish, with a thick head and a narrow tail. A cut should be made near the head.
2. Using sandpaper, you need to carefully sand the workpiece, removing all the irregularities.
3. Drill a small hole in the front. And along the entire body, make an axial hole through which the wire is threaded.
4. If the size of the bait is more than 7 cm, then it is worth installing an additional tee near the belly, where a hole is also made.
5. Fold the stretched wire into a loop on one side, and pull the other end through the body of the bait and make a loop.
6. Screw in another loop near the belly and secure the hook to it.
7. It is good to fill the attached wires with glue so that they sit firmly. Impregnate the wood itself with drying oil and cover it with a layer of paint.
8. When the workpiece is dry, attach the tee with the fly to the loop near the tail fin.

You can paint it any bright color. Blue, silver, red, gold work well. It is worth making several dark stripes along the body, they will give more realism.

Photo 3. At the popper manufacturing stage.

Fishing technique and tactics

In order for popper fishing to be successful, in addition to suitable gear, it is necessary to properly organize the process of hunting for prey. From the very beginning, it is necessary to study the reservoir and choose a promising location. This will help save a lot of time, because you won’t have to fish the entire body of water in search of the best place.

Advice! For popper fishing, it is better to choose separate areas near the coast. The predatory fish loves places overgrown with algae or snags. You can stop near a bend in the river or a shallow.

There are many factors to consider when choosing a location:

• lighting;
• wind direction;
• the presence of trees behind you that may interfere with casting.

Each fisherman chooses his own fishing technique. One of the most popular and effective techniques, how to catch a popper is considered a game with jerks and pauses. The frequency of jerks and their amplitude depend on the specific popper model.

If, when playing a popper, the bait gurgles, jumps and produces a fountain of water - this is a successful retrieve. The game should be stable and interesting, so it is worth experimenting and often changing techniques if the old one does not bring the desired result.

Poppers are unique baits that work on the very surface of the reservoir. If done correctly, they can gurgle and flap in the water, thereby attracting the attention of a predator.

One of the best spinning baits for surface fishing for predatory fish is a popper.

This attachment is easy to make with your own hands.

What kind of gear is this?

In spinning fishing in recent years, the dominant type of bait has become. Artificial fish are made in various modifications; they are capable of descending into the deepest holes or luring a predator to the surface.

One of the varieties of wobblers loved by spinning anglers has become. This superficial one is an oblong cylindrical fish with a concave nose. During a jerky stroke, the popper makes gurgling sounds and produces fountains of splashes like a follower of the butterfly swimming style.

The bait is most often used when fishing in grassy areas of a reservoir to lure fish from the algae to the surface. At the same time, many baits break off when caught on underwater obstacles.

Since the cost of a popper is quite high, and several models are required for fishing, many people make them with their own hands.

Making a popper with your own hands

There are several approaches to making homegrown poppers. Some of them are modifications of some fishing (and not only) accessories, while other products are made from scratch.

From the float

Many of us can find several abandoned floats in a fishing box or box. Some of them are quite suitable for turning into poppers.

For example, for perch fishing, you can make a surface bait from a match float of length 50 mm and thickness 9-11 mm. It is not so important what symbols are on the body of the float, the main thing is that its shape is similar to a popper. To work you will need a jigsaw, knife, wire, glue and a treble hook.

From a tree knot

It is not always possible to have an unnecessary float with the required dimensions at hand. After all, larger baits are needed.

You can make these poppers from natural wood. And in order to have less trouble with processing, you need to arm yourself with a caliper or ruler and choose a knot of an acceptable size. If a length of 50-60 mm is enough for a perch, then for a pike the bait should be 70-80 mm, and for a trophy predator - 100-110 mm. Ash, linden or birch are suitable materials.

There are many ways to increase your fish catch, but the most effective ones are. Below the site editors share with you the 3 most in effective ways increase in catch:

1. Electronic bait. Unlike conventional bait, which activates taste buds, electronic bait sharpens other types of nerve cells.
2. The new generation bite activator is no less effective. We invite you to familiarize yourself with the new product for 2019 - Fish XXL.
3. Learning different fishing techniques. For example, read about fishing techniques and fishing.

To make a bait you will need wire, a sharp knife, glue, sandpaper, paints and varnishes and tees with winding rings.

1. First, using a knife, file or emery, the required body shape is given. The tail part is made narrow, and an oblique cut is made in the head area.
2. All irregularities and roughness of the natural material are removed using sandpaper.
3. It is important to make a recess in the front part; a large drill or a table knife with a rounded tip is suitable for this.
4. An axial hole is made along the body of the bait using a thin and long drill. A wire structure will pass through it. In addition, when making a medium and large popper, provision should be made for installing an additional tee in the belly area. A neat hole is also made here.
5. The wire on one side is folded into a loop, and the straight end is pulled through the body. After this, an eyelet is made from the other edge. The same loop is screwed into the abdomen; you can first install a hook in the eye.
6. It is best to fix the wire structure with glue; be sure to soak the wood in drying oil and paint it.
7. After drying, a second tee with a front sight is mounted into the tail loop using a winding ring.

Transparent popper made from cork and syringe

A homemade popper with a rattle made of medical syringe. Since you can buy several disposable syringes at the pharmacy that differ in size, you get a whole arsenal of inexpensive poppers.
In addition to the syringe for making bait you will need:

The work consists of several simple steps:

1. The first step is to disassemble the syringe. After this, the spout is dismantled with a knife, and the ends of the stem are cut off.
2. It is necessary to cut out two unique plugs from the wine cork, the thickness of which is selected to match the inner diameter of the syringe. For precise work with a sharp knife, it is better to first mark the cork with a ballpoint pen.
3. One of the cork cylinders should be pierced with a wire and pushed inside the syringe until it stops. The end of the wire should come out.
4. The middle part of the rod is placed inside the syringe, and the balls from the bearing are placed in the resulting 4 sectors.
5. The second plug is also pierced with wire and inserted into the head part.
6. Using a drill, a through oblique hole is made through the belly of the future popper and the plug. Another piece of wire is pulled into it.
7. Using pliers, all that remains is to make three loops. A fishing line will be attached to the front one, and winding rings and tees will be installed in the back and belly eyelets. In addition, you can decorate the hooks with flies or strips of multi-colored foil.

The imagination of fishermen sometimes knows no limits.

To create a popper, both familiar materials and completely exotic things can be used.

With a creative approach to the manufacturing process, catchy ones can be obtained even from unusual items.

However only the predator will judge which of the fishermen will be right when creating a homemade popper.

Useful video

Video on how to make a catchy popper with your own hands:

Video about making a popper from a birch block with your own hands:

Vladislav Grushko

If you have built castles in the air, this does not mean that your work was in vain: this is exactly what real castles should look like. All that remains is to lay a foundation for them.

(Henry Thoreau)

Is it possible make a catchy bait with your own hands at home with minimal material costs and minimal woodworking skills? The answer is simple - you can! Using this homemade popper I managed to “persuad” predators of four species, thereby catching the Rapala Skitter Pop and more.

Dear spinning friends, we will make and assemble this truly catchy bait with our own hands, called a popper, from scratch. Its original purpose, first of all, is to catch perch, since the total size of the popper will not exceed 7 cm. Well, I think pike and other fish will also not refuse to taste it.

Stage 1

First, we need a branch of a “living” tree (preferably without knots). Fresh wood is easier to process than dry wood, which is why it is preferable. Any of the available ones will do - birch, linden, walnut or, like mine, maple (I just couldn’t find anything else at that time). We choose a tree with the smallest core diameter. Birch, for example, is a very sticky tree, and therefore it is not afraid of pike teeth, and such a popper will fly far. Linden, on the contrary, is very soft and pliable, it is much easier to process. Choose for yourself. We immediately estimate by eye or using a ruler what diameter we would like our popper to be (mine’s diameter is 1.6 cm). We make a choice in favor of the appropriate size - and go ahead.

We saw off, cut off all the leaves, branches, twigs we don’t need using a penknife or some other cutting object. The main advantage of working with a stick like this is that the shape of the future popper is almost ready, we just need to adjust it a little. And it’s very convenient to hold a piece of wood at one end, and at the same time plan out your “Pinocchio” from the other.

Stage 2

We clean the tree - remove the bark from it. Then, again by eye (as I do) or using a protractor, using a hacksaw we saw off the excess part of the wood at an angle of 45 degrees - this will be the head of our popper. If you can’t do it symmetrically, straighten the bevel with sandpaper. Next, using a small wood chisel (a penknife is also suitable), we make a small notch in the front part of the future popper (you can do this with a drill), the so-called “spitter”, which our popper will directly use to attract different fish. A more concave hole will give us a loud and “juicy” “gurgle”.

Having measured the length that suits us, without cutting off the other end of the branch (for convenience), we sharpen the tail part of the popper to the core, like a pencil. Now you can cut off the extra piece of wood. The length of my popper, from edge to edge, turned out to be 5 cm. The place where the popper began to narrow began after 3.3 cm, counting from the head. Now you can “sand” the popper blank with sandpaper with a grain size of 0.1 mm.

Stage 3

Now we need hard stainless wire. The diameter of the one I used is 0.8 mm (this thickness will be enough). And now the second advantage of working with knots as a material. Along its core (along), without any drills, drills or cuts, very easily and naturally, starting from the head of the workpiece, we pierce the popper through with wire. When the wood is fresh and the steel rod is fairly even, it won’t be too difficult to do everything very carefully and accurately.

At the head of the bait we make a small ring to connect to the leash. Applying a slightly metal rod to the tail, we hide the entwined, fixing turns of wire in the body of the popper. Leave the other end of the wire (no shorter than 3.5 cm) for now. Almost in the center of the popper (or rather, a little closer to the head), on its lower side, we pierce it again with another piece of steel rod, but we just do it even more carefully, since there is no core here and this will definitely be difficult to do.

Even if you didn’t get everything right the first time, that’s okay. Remove the wire and try again. We make a ring for the tee in the popper’s belly, and hide the excess in the body. On the back, we bend a small bracket from a protruding rod of wire (no larger than 1 cm in size) with round nose pliers and drive the end into the wood with a small hammer so that it is not noticeable.

Stage 4

Now, so that our popper is completely dry from the remaining juice (moisture), depending on the season, place it on the balcony or near the radiator (where it is warm and dry). After our popper is completely dry, we proceed to the next stage. Let's drop a drop of waterproof glue, which is good for both metal and wood, into all the junctions of the popper with the wire. This way, all the joints of the popper will be strong, water will not leak through and no predatory fish will tear out the wire. Leave to dry. After drying, so that our popper does not absorb moisture, we need to treat it. This can be done using nitro paints, alkyd varnish, or much easier and cheaper - drying oil. If you find it difficult to find this product, I suggest sunflower oil. You just need to heat it up a little (you can do it in a frying pan) and soak our popper thoroughly in it (5 minutes is enough). Once you remove the popper, it will darken. After one minute, instantly absorbing the remaining oil, the popper will become dry and non-greasy to the touch.

Stage 5

Next you can start painting the bait. I paint my poppers with quick drying fluorescent fishing varnish. This really saves a lot of time. After impregnating our popper with oil, it is no longer afraid of being chewed by pike teeth and you can easily, even while fishing, tint it with such fishing varnish. Regarding the color of the popper, I will say that the fish, due to the fact that the popper is located above it, cannot distinguish it. For her it is something dark, gurgling and very tasty. I painted my popper bright yellow and orange. They are very visible on the water and I just really like them. After several layers of varnish, the surface of the popper begins to feel like a soft eraser to the touch. Make a choice in favor of those colors that you like, and the fish will definitely bite, the main thing is not to doubt the color. Anyone who wants can draw or glue the eyes of the popper to make it look more like a fish; personally, I don’t do this.

Stage 6

The next step is to make the propeller for the popper. Most poppers do not have it, but I decided to increase the impact on predatory fish and attached a propeller. To do this, we need a sheet of hard metal about 0.4 mm thick, the main thing is that it is not too soft and does not have to be adjusted after each pike bite. It could be brass, copper, aluminum, galvanized or polymer-coated steel, like mine. Using a marker, draw the outlines of the future blades (not too thin - they will be deformed, not too wide - they will make it difficult for the popper to move). Using large and sharp stationery scissors (if you have metal scissors, that’s good)

cut out the propeller blank. Use a small nail or awl to make a hole for the wire, placing a wooden block under the screw. The diameter of the hole should be slightly larger than the steel rod for easy rotation of the propeller. Then smooth out all roughness with a file. Bend the blades in opposite directions so that they can rotate. The length of the propeller is 2.8 cm. This value was chosen for a reason, because if the propeller were shorter, the turbulent flows behind the popper would not allow its free rotation. A longer one, with such proportions, is also undesirable - the mass will increase (it will sink) or it may simply scare away the fish.

Stage 7

Now we need two beads or seed beads, but not too small. You can also use metal balls; of course, no pike can bite through them, but due to their weight they can pull the popper under the water, and we initially intended to design a floating one. Therefore, let’s focus on decorative beads. We string the first bead onto the part of the wire sticking out from behind, thanks to which we put a screw on our propeller, then another bead. We make a fastening ring for the threesome, wrap it around it,

wire in a spiral, bite off the excess end. The distance from the curled wire to the end of the popper itself was 1 cm. Longer is worse, this part may alert the fish, the propeller will not work well, and the same buoyancy may change. In short, it is also not advisable, because the propeller will be squeezed between the beads and will not rotate at all. The length from the beginning of the popper bevel to the end of the ring is 6.5 cm. I put a piece of thermophyte tube on the wound wire near the fastening ring and, holding it a little over the lighter, fixed it tightly (the thermofit shrinks in size by half when it is heated). As an alternative, a piece of cambric can serve. I do this so that the bead does not break on the hard wire; I hide unnecessary unwanted elements from the eyes of fish and simply for aesthetic reasons. This step is optional.

Stage 8

For this step I use colored rooster feathers as the fly. You can also use all kinds of cambrics, twisters, etc., but my experience shows that feathers are best option. I consider this stage mandatory. Some fish, especially perch, grab the popper exclusively by the fly; it irritates them very much. You need to take a very sharp and high-quality tee, because when fishing with surface baits there are many slippages. There is no need to skimp on this element. Very good threesomes from Owner.

The final stage of making a popper is to attach the tees using winding rings to the popper and catchable bait ready. The total weight of the popper was 7 grams.

This popper can be fished as a torpedo-type bait, just by rotating the handle of the reel, and like a regular popper, reviving it with the movements of the spinning rod. This kind of popper can rightfully be called an active bait. Due to the propeller and the fly at the back, it will not behave like a walker, yawing from side to side.

Have a nice catch!

One of the new baits, which is not yet known to a very wide range of anglers, is the popla popper.

It's quite interesting hybrid of float and popper, originally invented specifically for catching large rudd, but, as it turned out later, by choosing the right wiring and appropriate bait, you can successfully catch other types of fish with it. Having appreciated the full potential of this bait, many fishermen become its adherents, achieving success under the most unfavorable fishing conditions.

Detailed description of the bait

To put it simply, a popla popper is small float with popper properties. It has, as a rule, a drop-shaped shape, in its frontal part there is a familiar notch to create slurping sounds and splashes, but at the back, in the place where the classic popper has a tee, there is a regular loop for securing the leash.

They do not have a blade for deepening or a propeller. The leash is usually taken no longer than 12 – 15 cm, it is equipped with a single hook, preferably with a long shank. Some artificial bait imitating a worm, larva, etc. is attached to the hook. In some cases, to activate the bite, a live worm or maggot is attached. Fishing for it is done using a light spinning rod.

Today there are two types of this interesting industrially produced bait on the market:

1. MPP. They have a head size of 23 mm.
2. BPP. They have a slightly larger head - 30 mm.

The standard sizes of a pop-popper are very small; their length may vary, but, as a rule, it does not exceed 30 – 35 mm, and the weight is within 2 – 4 g. In this regard, it is not without reason that it is believed that the popla popper is intended for, or at least for light tackle.

They are released in three colors: white, yellow and the so-called “red fly agaric”, dark red, and BPP type baits come only in yellow and red. For greater visibility when fishing at long distances, some samples are marked with small black spots.

Key Benefits

Fishing with a popper is gaining popularity due to the following advantages:

1. Simplicity and efficiency of equipment.
2. Possibility of long casting (more than 30 m) when fishing with light and ultralight.
3. The resulting squelching sound effect attracts the attention of fish from a distance.
4. When fishing, cases of snagging and loss of gear are very rare. Thanks to this, you can fish in places with dense aquatic vegetation.

This bait, despite its small size, with proper wiring capable of attracting the attention of large fish.

Attention! Many experienced fishermen, when fishing with this bait, instead of a hook, attach a miniature jig head to a leash. Thanks to this, the bait sinks faster, which has a positive effect on the number of bites.

In addition to rudd, perch, asp, chub, and even grass carp and carp go well with it. When you attach a regular worm to a hook instead of artificial bait, you most often catch crucian carp.

Homemade popla popper

Some spinning anglers add various lures to their arsenal homemade popla poppers, fortunately, making it is not difficult at all and does not take long. A variety of available materials are suitable for its manufacture; it is quite possible to make a catchy popla popper even from a lollipop stick.

In this case, the main line passes through the stick with a stopper at the bottom. At the top of the stick, a small funnel or cone with a recess made of foam plastic or other dense material is placed on the glue. With its help, the necessary noise and splashes will be created during wiring. The result is a float capable of working like a popper when twitching the tackle with a fishing rod.

More popular materials for making a DIY popper are natural champagne cork or fine-grained, dense foam.

In order to make a good pop popper, you will need:

1. Natural cork or a small piece of dense foam.
2. A piece of stainless wire with a cross-section of 1 – 1.5 mm and a length of about 10 cm.
3. A small piece of lead or a small fishing shot.
4. Fishing line for a leash (you can use fruurocarbon).
5. Hook with long shank No. 5 – 7.
6. Sandpaper.
7. Waterproof glue and colored varnish (you can use nail polish).

You will also need a set of tools:

• sharp knife with a thin blade;
• pliers;
• round nose pliers;
• vice;
• wire cutters.

The production of a popper takes place according to the following algorithm:

1. From the material for the body (cork or polystyrene) we cut a piece about 30 mm long.
2. Using a knife, we give the body of the popper the shape of a large drop with a blunt nose.
3. Using a knife and coarse sandpaper, we make a cup-shaped depression in the bow, which will be responsible for the sound and splashes. You can also do it using a drill of a suitable diameter (28-30 mm).
4. We sand the entire surface of the bait to give it a complete shape.
5. We make a fastening for the leash and the main fishing line from wire. You need to bend it so that you get loops on both sides of the fastener. Make sure the lengths of the parts are correct.
6. A longitudinal incision is made in the body to the central center line. We insert the mount there.
7. A small plate of lead needs to be inserted into the same cut, serving as a weight for the bait. After this, fill the cut with waterproof glue (you can use epoxy resin) and carefully clamp the workpiece in a vice until it dries.
8. The bait is sanded with fine sandpaper.
9. Next, you need to paint it with varnish of the chosen color and let it dry. Repeat this procedure twice.
10. We attach a leash with a hook to the back ring.
11. You can attach a carabiner to the front ring for more convenient changing of bait while fishing.

That's it, the homemade popla popper is ready for fishing.

Important! The weight of the load is selected taking into account that the bait should not sink, it should only submerge it a little. Thanks to this popla, the popper does not twist and always remains in one position (the heavier side is always below).

It’s quite possible to make several of these baits in one day. different sizes and different colors.

Features of using bait

Of course, fishing with popla popper is very exciting and belongs to active species fishing. You can catch both ordinary, peaceful fish and predators.

In order for fishing to be effective, you need to select the appropriate equipment for it. The popla popper rig has its own characteristics:

1. Light class rod should not be longer than 2.4 meters, even if casting is done from the shore. With such a fishing rod it is easier to make long and accurate casts of light bait.
2. It is better to take a light reel(1000 – 1500), inertia-free type. The sensitivity of the gear largely depends on the quality of its work.
3. More suitable as a main fishing line small diameter braid. It is able to withstand the resistance of a large rudd or other fish, even if it goes into the reeds after hooking. Enough fishing line with breaking load up to 5.5 kg.
4. Hooks must be of high quality, designed for the fact that grass carp may also be caught, capable of unbending them during an active fight.

As a rule, fishing for popla popper takes place on overgrown areas of the reservoir, where they try to throw it into a clean window in the middle of vegetation or on the border between the grass and a clean area of ​​​​the reservoir. An important element The key to attracting the attention of fish when fishing with this bait is the technique of its placement:

• if the fish is active, then apply classic way to carry out poppers, quick jerks with short pauses of 2–3 seconds;
• if the fish is inactive, then pauses need to be increased, giving the fish a better look at the bait on the hook.

In addition, it has been noticed that at different times baits of different colors are more catchy:

• early spring or late autumn, and also on a sunny summer day, red and yellow poplar poppers work better than others;
• The white color attracts fish when fishing in the shade of trees or under bridges.

One more interesting feature This equipment is that when retrieving a popper, the popper attracts fish with its sounds and splashes, and during pauses it becomes an ordinary float - a classic bite alarm.

Knipovich Nikolai Mikhailovich

Zoologist, hydrobiologist. Graduated from Leningrad State University named after Zhdanov, Faculty of Biology and Soil Sciences. I am interested in fishing at a professional level.